5.5 kW Water Cooled Spindle Motor, 18,000rpm, 380V

Stock: In Stock
Model: GDK120-9-18Z/5.5-11
SKU: PEACO-SPINDLE-14

Based on 0 reviews. - Write a review

$1,195.84

Ex Tax: $1,195.84

Qty

Add to Cart

Buy Now

Add to Wish List

Free Shipping Worldwide.

By DHL/ FedEx/ UPS.

Lead Time 7-12 Days.

Mail Us for Lead Time of Custom Products.

MOQ 1.

Buy More Save More.

5.5 kW water cooled spindle motor features 5.84 N.m - 2.29 N.m torque, max. 18,000rpm running speed. The 380V CNC spindle motor is a kind of constant torque spindle, comes with ER25 collet, efficient water cooling and low noise level and suitable for stone carving / metal engraving.

Specifications

Model: GDK120-9-18Z/5.5-11
Material: Stainless steel, copper, aluminum
Power: 5.5 kW
Torque: 5.84 N.m - 2.92 N.m
Voltage: 269V-380V
Current: 15.5 A
Frequency: 450Hz-900Hz
Speed: 9,000-18,000 RPM
Cooling: Water-cooled
Bearing Lubrication: Grease
Number of Pole: 2 poles
Joint of Nose: ER25 collet (Φ3.175 mm-Φ16.0 mm)
Bearings Type: 7007C (P4)*2, 7005C (P4)*2
Dimension: ØD=125mm, ØD1=100mm, L=365mm, L1=32.5mm, L2=56mm
Rotating Mode: anticlockwise from the shaft extension end.
Net Weight: 21kg
Gross Weight: 28kg (packed with wooden box)
Certification: CE
Warranty: 1 year

Spindle Motor Dimension (Unit: mm)

Spindle Motor Wiring

Warning:

1. The electric main shaft shall be installed at the clamped position, otherwise the bearing will be easily damaged.

2. The compressed air shall be dry and clean and the filtering accuracy shall be 0.1 micron. Atmospheric pressure is 0.1- 0.2 MPa and the air seal shall be normally open. It is recommended to use the two-level filtration with the filtration accuracy of 0.5 micron / 0.1 micron respectively and the air filter shall have automatic discharge device.

1. The electric spindle should be used with VFD, and the specifications and setting parameters of the variable frequency drive should match the rated parameters of the spindle. If there are wrong settings, the spindle motors will be burned.

2. Before using the water-cooled CNC spindle motor, users should guarantee that the cooling circulation system works normally. It is strictly forbidden to use it without cooling. Additionally, the cooling water volume should be calculated at 1 liter/kW min and the connection between the cooling pipe and the nozzle must be reliable and does not allow leakage.

3. The cooling liquid for spindle must be clean and non-greasy, and the temperature should be controlled at 5°C-30°C. If the ambient temperature is more than 30°C, the cooling medium must be forced to refrigerate. Precision machine tools require coolant with constant temperature 20±2℃.

4. During the storage and transportation of the spindles, the state of the high-speed grease inside the bearing will change, and users should run it at a low speed before using it. The running-in starts from the lowest speed of the electric spindle, and after 30 minutes, the speed is increased according to the 3000-rpm step difference. Users make it run for 20 minutes for each gear. If users start the spindle at high speed without running in, there will be abnormal sound, noise, heat and other phenomena, which will impact the service life of the bearing. During the long-term use and storage of the electric spindle, it should be turned on (at low speed) for 15-30 minutes within one week at least.

5. When the spindle is clamped with tools, the collet, nut and inner taper hole must be cleaned to avoid affecting the accuracy. The tool handle must be inserted into the collet with more than 15mm depth.

6. The electric spindle must be preheated every day before processing. After the spindle reaches the processing speed, finish machining can be done after running for 5-20 minutes. It is advisable to stop the spindle motor for 2 hours every day to restore mechanical fatigue and prolong its service life.

7. It is strictly forbidden to strike the end cover of the spindle and to strike the collet and cutter head when users unload the knife. Bumping is strictly prohibited during transportation, storage and use, especially the shaft end should be kept well.

8. The electric spindle must run in the specified direction.

9. Please follow the instructions in the spindle clamping diagram for clamping the electric spindle.

10. When the user uses the water cooler for cooling, the temperature must be controlled at 22-25℃.

11. The electric spindle should be used with an air seal, and the air source must pass through an oil-water separator and a dry filter before use. The air pressure is 0.2-0.25MPa, and the filtration accuracy is 5μm, otherwise the bearing will be damaged.

5.5 kW Water Cooled Spindle Motor, 18,000rpm, 380V

Write a review

You may also like

About Us

My Account

Customer Service