The DC contactor relay is a high voltage DC contactor, featuring main contact current 250A, optional auxiliary contact 1NO, coil rated voltage can be 9V-36V, energy-saving circuit board is equipped in the contactor and other coil voltage and coil lead length can be customized for your special requirement.
1. The reliable sealing enables the DC contactor relay to be used in harsh and explosion-proof environments for a long time and its internal components including coils and contacts are not oxidized. The DC contactor also features fast switching action, low energy consumption, low heat generation, long life, small size and light weight.
2. The DC contactor relay can control high voltage and high current and has auxiliary contact for better performance. The contact is protected by a strong magnetic arc blowing, thereby prolonging its service life.
3. Smaller arcs make the contactor more effective and safer to use. The relay is sealed with inert gas, which ensures that there is basically no arc between the contacts when the contactor is in action and magnetic blow-out is adopted to ensure safety.
4. High stability. The internal mechanism and structure of the contactor are completely sealed with the inert gas, free from the interference of adverse external factors and the contact resistance remains stable for a long time.
5. Wide application. DC contactor relays are widely used for DC power control, battery switch control, circuit safety protection, etc.
|Coil||Rated Working Voltage (Us)||9-36V DC|
|Working Voltage Range (20℃)||9-36V DC|
|Pull-in voltage (20℃)||8V-9V|
|Release voltage (20℃)||6V-7V|
|Coil power (20℃)||2W (Maintain)|
|Main contact||Max. continuouse overcurrent||250A|
|Contact voltage||12-900V DC|
|Rated control capacity||250A 450V DC|
|Short-time withstand current||350A 900S|
|Contact pull-in time||30ms max.|
|Contact release time||10ms max.|
|Max. breaking current (＞1 time)||2000A 350V|
|Contact type||1 set normal open|
|Contact polarity||polarity or nonpolarity|
|Contact resistor||≤ 2mΩ|
|Auxiliary contact||Contact form||1 set normal open|
|Contact resistor||15mΩ max.|
|Max. load||2A 30V DC, 3A 125V AC|
|Life time||Machanical life||200,000 times|
|Electrical life (L/R ≤1ms)||6,800 times|
|Dielectric properties||Between contacts||3500V AC/ 60 Sec/1mA|
|Between contacts and coils||2500V AC/ 60 Sec/1mA|
|Mechanical property||Impact||20G peak value, 11 ms 1/2 sine wave
(coil electric connection)
|Vibration||20G peak value, 8-2000Hz sine wave|
|Working Environment||Environment temperature||-40℃~+85℃|
- Drive and control systems for mining equipment and mechanical vehicles.
- Power control, circuit insulation of industrial machinery.
- DC switch equipment.
- Car battery power distribution and backup.
- Hybrid electric vehicles, electric vehicle charging piles and other fields.
- Solar and wind power generation, etc.
DC Contactor Relay Dimension (Unit: mm)
1. When installing the DC contactor relay, a washer should be used to prevent the screw from loosening.
2. DC contactors with polarity shall be wired according to the marks on the product cover, there are no any requirements of incoming and outgoing lines for nonpolarity contactors.
3. Do not install the contactor in a strong magnetic field environment (near the transformer or magnet) or near the heat radiation source.
4. Do not use the contactor when its switching capacity and service life parameters are exceeded.
5. Make sure the working environment temperature between -40°C ~+85°C, too high temperature is easy to accelerate the diffusion of internal inert gas and it is necessary to avoid using the product under too high temperature environment.
6. When the resistive load is connected, it shall be used according to the rated parameters of the main contact. If the inductive load (L load) is connected and L/R > 1ms, the inductive load shall be connected in parallel with the surge current protection device.
7. During wiring and installation, to ensure that the main outgoing end and terminal head are clean and tightened to avoid excessive heating at the connection of outgoing end.