100W Wind Turbine, 12V/24V, 3 or 5 Blades
- Stock: In Stock
- Model: PNE-100S
- SKU: PNE-100S
$306.79
Ex Tax: $306.79
High efficiency 100W wind turbine works with 2.0m/s start-up wind speed, 12V or 24V rated voltage, 3 or 5 nylon fiber blades can be selected. Equipped with three phase AC permanent magnetic wind turbine generator. High wind power utilization, high conversion rate, low vibration.
Specification
| Model | PNE-100S | Start-up Wind Speed | 2.0m/s |
| Rated Power | 100W | Rated Wind Speed | 10m/s |
| Maximum Power | 130W | Safe Wind Speed | 55m/s |
| Rated Voltage | 12V/24V | Wind Wheel Diameter | 1.2m |
| Wind Turbine Blades Qty | 3 or 5 (Optional) | Controller System | Electromagnetic |
| Blades Material | Nylon Fiber | Wind Direction Adjustment | Automatically adjust windward direction |
| Generator Type | Three-phase AC permanent magnet | Installation Flange | DN20 |
| Magnetic Steel Material | NdFeB | Working Temperature | -40°C~80°C |
| Generator Shell Material | Die-casting Aluminum | Certificate | CE |
| Net Weight | 8.5 kg | Service Life | 15 years |
| Gross Weight | 9.5 kg | Warranty | 3 years |
1. Low start-up wind speed. The lowest speed is up to 2.0m/s and the starting with breeze can be achieved.
2. High wind energy utilization and large annual power generation. Blades are molded through precision injection with new technology and generator is three phase AC permanent magnetic. It's a clean energy solution for a new generation of wind turbine.
3. High quality. The tail part is made of high quality ABS material and blades are manufactured with nylon fiber.
4. Light weight, strong stability. It's easy to install, operates with low vibration and the cost can reduced.
5. High efficiency. The thickness of the coil is a key part of the power generation. The stator windings are enlarge and and quality copper wires are adopted to improve the power generation efficiency of the motor at low speed.
6. High performance. Rotor magnet thickness is increased and double bearings are upgraded. Double ball bearings are used to prevent vertical vibration, improve efficiency, reduce noise and increase yaw stability.
7. Wide Application. Ideal for home use, camping in forest, monitoring use, boat/marine use, wind-solar hybrid streetlight use, etc.
100W Wind Turbine Exploded View
1. Wind turbine body 2. Wind turbine flange seat 3. Tower 4. Wind turbine shaft 5. Wind hub
6. Wind wheel 7. Lock nut 8. Fairing 9. Bolt 10. Flat washer 11. Elastic washer 12. Nuts
13. Stainless steel nut 14. Anti-loose nut 15. Rubber pad
KNOWLEDGE BASE --- Wind Turbine Technical Principle
In general, when wind passes through the wind turbine, almost half of the air is forced to stay around the blades instead of passing through them and the energy in the wind is lost. Only 59.3% of the wind energy can be used on traditional wind turbines and this value is called the Betz limit.
The design of wind turbines based on jet engine technology overcomes a basic defect existing in traditional wind turbines. The wind turbine blades are covered with shields to guide air to pass through the blades and accelerate them, which increases electricity production. Wind turbines are like the air intakes of jet engines. When air enters, it first encounters a set of fixed blades called a stator, which can guide the air into a set of rotatable blades (the rotor). The air pushes the rotor and appears on the other side. At this time, the speed of air flowing is slower than that of the air flowing outside the turbine. The shield is made into a special shape so that it guides the air that flows outside relatively fast into the area behind the rotor. The fast-moving air accelerates the slow-moving air, making the area behind the turbine blades low pressure area so as to store more air through blades.
